MAKS WDC mini – is a wireless magnetic contact designed to monitor the status of structural elements (open/close) to detect an attempt to enter a room. The device sends an alarm notification to the alarm center MAKS PRO security alarm system.
Mounted indoors and used to protect doors and windows.
- miniature sensor
- efficient on metal doors
- secure two-way radio communication with MAKS PRO
- 868.0 … 868.6MHz, several channels for redundancy
- range up to 4800m in line of sight
- lithium battery CR2, up to 5 years of operation
- easy and fast installation
- secure fastening
- available in three colors
| Reed switch | threshold 7-15 mm, operations > 1 000 000 |
| Power | 3V, CR2 lithium battery included |
| Service life of battery | up to 5 years |
| Radio frequency | ISM-band wireless interface, multi-speed with several channels. Three grades of power ITU region 1 (EU, UA): 868.0 to 868.6 MHz, bandwidth 100kHz, 20 mW max., up to 4800m (in line of sight) ITU region 3 (AU): 916.5 to 917 MHz, bandwidth 100kHz, 20 mW max., up to 4800m (in line of sight) Russian Federation: 868.0 to 868.2 MHz, bandwidth 100kHz, 10 mW max., up to 3200m (in line of sight) |
| Communication | Secure two way communication, sabotage detection, key – 256 bits |
| Operating temperature range | -20°C to +50°C |
| Dimensions | 85 х 18.5 х 17.6 mm |
| Magnet dimensions | 85 х 11 х 6 mm |
| Case colour | white, dark brown, black |
| Weight | 56 grams |
The device uses an CR2 battery (included):
- Up to 5 years of operation
- Standby consumption < 2 µA
- Transmission consumption < 45 mA
CAUTION. RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE USED BATTERIES ACCORDING TO THE NATIONAL REGULATIONS.
1. Bottom plate of magnet case
2. Magnet case cover
3. Neodymium magnet
4. Bottom plate of the detector case
5. Detector case top cover and capsule with the device
6. Magnet position marks
7. LED indicator
8. Tamper switch
9. On/off button
10. Battery CR2
Press button to turn on the device – the indicator will be on. If the device is registered in the MAKS PRO, it switches to standby mode.
To turn off the device, press and hold button for 5 seconds.
CAUTION. IF THE SENSOR IS NOT REGISTERED, IT WILL SWITCH TO SLEEP MODE AFTER 30 SECONDS.
1. Start the MAKS Setup application
2. Follow the instructions of the application to connect to the MAKS PRO and start the registration of MAKS wireless devices
3. Turn on the MAKS WDC mini
4. Place the detector at a distance of no more than 2 m from the MAKS PRO control panel
CAUTION. THE REGISTRATION RUNS AT THE LOWEST POSSIBLE POWER TO AVOID THE INFLUENCE OF NEIGHBORING SYSTEMS WHICH CAN BE BEING SET UP NEARBY.
5. In 10-20 seconds device will be registered
6. Set up a new device in your mobile application
1. Start the MAKS Setup application
2. Follow the instructions of the application to connect to the MAKS PRO and start the range test
3. Trigger the detector to switch to a test mode faster
4. Move the device. Select the location with the optimal signal level based on the information in the application or the light indication
5. The device will automatically exit the test mode after 30 minutes. You can stop test mode in the mobile application.
CAUTION. IN TEST MODE, THE DEVICE’S RADIO TRANSMITTER OPERATES AT MEDIUM POWER.
Indication in range test mode
- Excellent connection – LED indicator flashes green
- Normal connection – LED indicator flashes yellow
- Poor connection – LED indicator flashes red
- No connection – LED indicator flashes red quickly
Carefully select the installation location. The device should not be placed:
- Outdoors or in areas with unacceptable humidity and temperature
- In places with a high level of radio interference
- Near objects that can cause radio signal attenuation or shielding (metal, mirrors, etc.)
- At a distance of less than 1 m from the security center
We recommend to install the device in the following order:
- Selecting the installation location with the best signal using the MAKS Setup application. Note the sensor can be placed vertically or horizontally.
- Mount the magnet
- Install the detector bottom plate, due to mark on the detector case
- Install the device
Caution! When the capsule is inserted correctly, the tamper must be clamped (locked).
Vertical placement
1. Mounting the magnet
2. Installation of the detector bottom plate
3. Installation of the device
Horizontal placement
1. Mounting the magnet
2. Installation of the detector bottom plate
3. Installation of the device
- miniature sensor
- efficient on metal doors
- reliable radio communication over long distances
- available in three colors
Warranty for MAKS devices (except batteries) is valid for two years after the purchase date.
If the device operates incorrectly, please contact support team at first, maybe it can be solved remotely.