MAKS WDC manual

Description

MAKS WDC – is a wireless magnetic contact designed to monitor the status of structural elements (open/close) to detect an attempt to enter a room. The device sends an alarm notification to the MAKS PRO control panel.

Equipped with two reed switches, mounted indoors and used to protect doors and windows.

The detector has contacts for connecting the arming information LED and external reed switch.

  • efficient on metal doors
  • secure two-way radio communication with MAKS PRO
  • 868.0 … 868.6MHz, several channels for redundancy
  • range up to 4800m in line of sight
  • lithium battery AAA, up to 3 years of operation
  • easy and fast installation
  • secure fastening
  • available in three colors
  • MAKS WDC
  • MAKS WDC
  • MAKS WDC

Characteristics

Sensors 2 built-in reed switches and external sensor connector
Anti-sabotage function only one of the sensors can be in normal state
Reed switches threshold 7-15 mm, operations > 1 000 000
Power 1.5V, AAA (FR03) lithium battery included
Service life of battery up to 3 years
Radio frequency ISM-band wireless interface, multi-speed with several channels. Three grades of power
ITU region 1 (EU, UA): 868.0 to 868.6 MHz, bandwidth 100kHz, 20 mW max., up to 4800m (in line of sight)
ITU region 3 (AU): 916.5 to 917 MHz, bandwidth 100kHz, 20 mW max., up to 4800m (in line of sight)
Russian Federation: 868.0 to 868.2 MHz, bandwidth 100kHz, 10 mW max., up to 3200m (in line of sight)
Communication Secure two way communication, sabotage detection, key – 256 bits
Operating temperature range -10°C to +55°C
Dimensions 138 х 20.75 х 17.1 mm
Magnet dimensions 85 х 11 х 6 mm
Case colour white, dark brown, black
Weight 65 grams

Battery

The device uses an AAA battery (FR03 1,5 V):

  • Up to 5 years of operation
  • Standby consumption < 5 µA
  • Transmission consumption 70 мА

Lithium batteries (FR03) Recommended (included)
Alkaline batteries (LR03) Usage allowed at temperatures above +5°C
Salt batteries (R03) Do not use!

 

CAUTION. RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.
DISPOSE USED BATTERIES ACCORDING TO THE NATIONAL REGULATIONS

Functional parts

1. Bottom plate of magnet case
2. Magnet case cover
3. Neodymium magnet
4. Bottom plate of the detector case
5. Magnet position marks
6. Capsule with the device
7. Position of reed switches in the capsule
8. LED indicator
9. Top tamper switch
10. Battery (AAA)

11. Wires for:

  • LED connection (LED, contact LD+)
  • common wire (C contact, ground)
  • reed switch connection (DC contact)

12. External Wire Connection
13. On/off button
14. Bottom tamper switch
15. External reed switch
16. External LED
17. Detector case top cover

Switching on and off

Press button to turn on the device – the indicator will be on. If the device is registered in the MAKS PRO, it switches to standby mode.

To turn off the device, press and hold button for 5 seconds.

CAUTION. IF THE SENSOR IS NOT REGISTERED, IT WILL SWITCH TO SLEEP MODE AFTER 30 SECONDS.

Registration

1. Start the MAKS Setup application

2. Follow the instructions of the application to connect to the MAKS PRO and start the registration of MAKS wireless devices

3. Turn on the device

4. Place the device at a distance of no more than 2 m from the MAKS PRO control panel

CAUTION. THE REGISTRATION RUNS AT THE LOWEST POSSIBLE POWER TO AVOID THE INFLUENCE OF NEIGHBORING SYSTEMS WHICH CAN BE BEING SET UP NEARBY.

5. In 10-20 seconds device will be registered

6. Set up a new device in your mobile application

Range test

1. Start the MAKS Setup application

2. Follow the instructions of the application to connect to the MAKS PRO and start the range test

3. Trigger the detector to switch to a test mode faster

4. Move the device. Select the location with the optimal signal level based on the information in the application or the light indication

5. The device will automatically exit the test mode after 30 minutes. You can stop test mode in the mobile application.

CAUTION. IN TEST MODE, THE DEVICE’S RADIO TRANSMITTER OPERATES AT MEDIUM POWER.

INDICATION IN RANGE TEST MODE

  • Excellent connection – LED indicator flashes green
  • Normal connection – LED indicator flashes yellow
  • Poor connection – LED indicator flashes red
  • No connection – LED indicator flashes red quickly

Installation

Carefully select the installation location. The device should not be placed:

  1. Outdoors or in areas with unacceptable humidity and temperature
  2. In places with a high level of radio interference
  3. Near objects that can cause radio signal attenuation or shielding (metal, mirrors, etc.)
  4. At a distance of less than 1 m from the security center

We recommend to install the device in the following order:

  1. Selecting the installation location with the best signal using the MAKS Setup application. Note the sensor can be placed vertically or horizontally.
  2. Mount the magnet
  3. Install the detector bottom plate, due to mark on the detector case
  4. Install the capsule with the device
  5. Close the device case

Caution! When the capsule is inserted correctly, the tamper must be clamped (locked).

Vertical placement

1. Mounting the magnet

2. Installation of the detector bottom plate

3. Installation the capsule with the device

4. Close the device case

Horizontal placement

1. Mounting the magnet

2. Installation of the detector bottom plate

3. Installation the capsule with the device

4. Close the device case

External sensor connection

Connection of NC (normal closed) external sensor

Connection of NO (normal open) external sensor

Features

  • Capsule construction
  • Efficient on metal doors
  • Reliable radio communication over long distances
  • Available in three colors

Warranty

Warranty for MAKS devices (except batteries) is valid for two years after the purchase date.

If the device operates incorrectly, please contact support team at first, maybe it can be solved remotely.